B8056G68AE12HR-2T LED drive locate raw commands

Modify last hex to change LED status.

(normal=0x00，blink (1HZ)=0x01，remains on (no blink)=0x02，blink (4HZ)=0x04)

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x01 0x04 -----HDD0

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x03 0x04 -----HDD1

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x05 0x04 -----HDD2

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x07 0x04 -----HDD3

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x09 0x04 -----HDD4

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x0B 0x04 -----HDD5

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x0D 0x04 -----HDD6

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x0F 0x04 -----HDD7

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x11 0x04 -----HDD8

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x13 0x04 -----HDD9

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x15 0x04 -----HDD10

ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC0 0 0x17 0x04 -----HDD11

Related Articles
B8056T70AE26HR-2T LED drive locate raw commands
Modify last hex to change LED status. (normal=0x00，blink (1HZ)=0x01，remains on (no blink)=0x02，blink (4HZ)=0x04) First backplane: ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC6 0 0x01 0x04 -----HDD0 ipmitool raw 0x2e 0x09 0xfd 0x19 0x0 0xC 0xC6 0 0x03 ...
B8261T85E24HR-2T LED drive locate raw commands
The First BP: (i2c bus=30(0x1e)，CPLD address=0xc0) (normal=0x00，blink (1HZ)=0x01，remains on (no blink)=0x02，blink (4HZ)=0x04) HDD0 blink: (offset: 0x01) ipmitool raw 0x2e 0x09 0xfd 0x19 0x00 0x1e 0xc0 0x00 0x01 0x04 HDD1 blink: (offset: 0x03) ...
How to locate HDD in B8056 by ipmitool raw command
For SKU B8056T70AE26HR & B8056T70V8E6HR
Intel Server Board S2600WF_Cohesity_Drive Reseat_replacement
Intel Server Board S2600WF (Cohesity) Storage Drive/Cable Reseat: (1) Drive Reseat/Replace - The steps below can be performed while the server is running. a. Identify the correct slot location depending on the chassis type 1U System Figure 1 R1208 - ...
How to set Micron 7500 series U.2 idle LED on B8056T70AE26HR-2T NVME#24&25
The LED behavior on the 7500 series is configurable via vendor-unique (VU) NVMe commands. Specifically, the LED configuration can be adjusted using the 0xF2 feature code. For example: To set LED to be OFF during Idle: sudo nvme admin-passthru ...

Related Articles